Basic HTML Version
167
FOUR
STROKE
INTAKE
SYSTEMS
ENGINE/
GASKETS
EXHAUST DRIVE LINE
HANDLING
ELECTRICAL WATERLINE
/BILGE
STEERING
& CONTROLS
BODY
ACCESSORIES
SERVICE TOOLS
/HARDWARE
CHEMICAL
©2012 Hot Products. All rights reserved.
R&D’S “BIG ASS” PROP WRENCH
R&D's Big Ass prop wrench takes the fight out of removing any tough to
remove prop. Changing the prop at the beach without a vise is no prob-
lem. Also light enough to carry in your luggage while traveling to interna-
tional races. The key is LEVERAGE! The 28” long wrenches are made
from ?” plate aluminum and utilize an ID hex to get maximum bite without
slipping on the prop tool. With these tools your prop changing headaches
are over, guaranteed. Measure your existing spline tool and Solas or
Skat-Trak prop tool and order the proper size wrenches.
Description
Part No.
Fits Skat-Trak Prop Tool for Super Jet/Raider/Blaster
132-56001
Hex size .875”
Fits Solas Shaft Spline Tool for Super Jet
132-56002
Hex size .910”
Fits Skat-Trak Prop Tool for
132-56003
SHO/FZR/FZS/GPR/HO/FX/VX
Hex size 1.000”
Fits R&D Shaft Spline Tool for SHO/FZR/FZS
132-56004
Hex size 1.125”
Fits Solas Shaft Spline Tool for GPR
132-56005
Hex size 1.150”
Fits Solas Tool 1.175”
132-56006
Hex size 1.175”
Fits Solas Prop Tool for SHO/FZ
132-56007
Hex size 1.415”
SOLAS STAINLESS STEEL YAMAHA
12-VANE STATOR SECTION
Get HUGE gains in Hook Up on bottom end, and overall efficiency in rough
conditions, and jet wash! This pump is a must have for Freestyle! The Brand
New Solas Yamaha 144mm 12 Vane Pump Stator is now available and is an
incredible value for the HUGE performance gain resulting from bolting this
pump on!
This is the stator section only, is stainless steel, with large diameter bearing
carrier, and a 12 vane standard position design. It replaces the stock Yamaha
144mm 6 vane aluminum stator section. No need to buy an expensive
extended shaft with this pump conversion.
You will need a large hub design impeller such as the Impros Hooker
impeller, the Solas Concord YQ-CD, or Skat-Trak C+75 Swirl impeller with
this pump.
Yamaha
Part No.
Stainless Steel Yamaha 12-Vane Stator
YQS-SV-144
A.
Impros Pump Spacer
IMYQ-NS
(required when Solas pump stator is used with stock nozzle)
B.
Impros Freestyle Tail Cone
IMYQ-FC
WSM Yamaha Pump Bearing & Seal Kit
003-630
A.
SOLAS 12-VANE PERFORMANCE
PUMP FOR KAWASAKI
The Solas Kawasaki High Performance 12 Vane Pump is a stainless steel
vane, 140mm diameter with 75mm bearing carrier, pressed into an aluminum
housing. It is a "Standard Position" pump, meaning, it is not set back, and
you can use your existing driveshaft (no extended shaft necessary).
It comes complete with bearings, seals, pump shaft, and tail cone and to top
it off, an adjustable diameter drop nozzle system!
The pump fits the 2003-2012 Kawasaki 800 SXR. It also fits the 1992-2002
750 models SX, SXi, SXi Pro, SS, ST, Xi, and XiR.
This pump kit does not include an impeller, trim system cable, or lever, we
suggest using either the Solas KP-DF impeller, or the Skat-Trak C-75
Magnum Swirl impeller.
These pumps really improve rough water performance, and they fit right up
to the hull like an OEM pump.
Description
Part No.
Solas 12 Vane Performance Pump
KPS-PM-140/74T
with Trim System for Kawasaki
B.