Basic HTML Version
PRO-CRIMP TOOL
To do a job right, it is important to have the right tools. If you custom build a lot
of plug wires, the Pro-Crimp is the right tool for you! The Pro-Crimp features a
hardened steel frame, molded hand grips and built-in ratchet action that is also
adjustable. The tool is supplied with jaws to fit MSD’s Super Conductor Spark
Plug wires and can be removed to use additional jaws (not supplied) for
crimping common wiring terminals.
101
FUEL
SYSTEMS
ENGINE/
GASKETS
EXHAUST DRIVE LINE
HANDLING
ELECTRICAL
WATERLINE
/BILGE
STEERING
& CONTROLS
BODY
ACCESSORIES SERVICE TOOLS
/HARDWARE
CHEMICAL FREESTYLE
& 800SXR
FOUR
STROKE
Description
Weathertight 6 pin connectors
Weathertight 4 pin connectors
Weathertight 3 pin connectors
Weathertight 2 pin connectors
Grey Deutsch 8 pin connectors
Grey Deutsch 6 pin connectors
Grey Deutsch 4 pin connectors
Grey Deutsch 2 pin connectors
Part No.
8170
8171
8172
8173
8185
8180
8181
8183
MSD WEATHERTIGHT & DEUTSCH CONNECTORS
Weathertight
Grey Deutsch
Description
MSD Timing Light
Part No.
8990
MSD TIMING LIGHT
MSD offers a heavy duty top quality timing light. This timing light is supplied in
a heavy duty metal housing and features a high output Linear Xenon strobe
with a focused fresnel lens that produces a light that’s bright enough to use
outdoors. It is equipped with a 6 foot lead and uses a metal inductive pickup
that clamps to the spark plug wire.
Description
Part No.
MSD Pro-Crimp Tool
3505
Spark Plug Dies
3508
Amp Pins
3506
Amp Lug Dies
3507
Weathertight Dies
3509
Deutsch Terminal Dies
3510
PERMA-SEAL CONNECTION KIT
Maximum ignition reliability can only be obtained by using high quality
connectors and the Perma-Seal Connector Kit fits the bill! The tin coated
copper terminals prevent corrosion and increase the connector’s strength. To
seal the connection, each connector has a special heat shrinkable outer sleeve
that bonds and seals to the wire when heat is applied to it.
Description
Part No.
MSD Perma-Seal Connector Kit
4377
PROGRAMMABLE PULSE WIDTH
MODULATED WATER INJECTION
Stock and performance exhaust systems are designed for maximum power at
a specific rpm. It’s not really something you can change during a race, and we
know that compromises power at other rpm. Racers don’t like to compromise,
so MSD offers a new Programmable Water Injection system so you can tune
your exhaust to match any rpm!
By injecting water into the exhaust chamber at lower rpm, the density of the
exhaust pulse is increased, which slows it down.This has the same effect as
lengthening the chamber to increase low to mid-range torque and power! The
Programmable Water Injection system uses MSD’s Pro-Data+ Windows based
software so you can easily program how much water and at what RPM it gets
injected into the pipe. The programming features allow you to inject water from
0 to 100 percent anywhere from 500 rpm to 12,000 rpm.
The kit comes complete with spray nozzles, solenoid, heat resistant hose,
programmable controller and software.
Description
MSD External Starter Relay
Part No.
4390
MSD EXTERNAL STARTER RELAY
This 12 volt relay is a heavy duty unit designed to mount outside the electrical
box. It’s made with material that locks out moisture and chemicals. The large
copper terminals assure good solid contact with your wiring. The stainless steel
base plate allows the relay to be mounted in any position. Rated at 65 amps.
Description
Part No.
Programmable Water Injection Control System
42590
Water Injection Solenoid Only
4340
Hand held Programmer/Monitor
7550
42590
7550