2012 Hot Products Catalog

81 KAWASAKI 4 STROKE INATKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ULTRA 250/260/300 • PUMP ©2012 Hot Products. All rights reserved. WET WOLF ADJUST-A-THRUST Kawasaki STXR, STX12F, Ultra 250/260 and Ultra 300 pumps. Comes with shorter impeller shaft and bearing already installed into the body. Bearing changes in the tail cone are made easier due to the fact that the bearing is located at the bottom of the unit, instead of in a deep pocket like the stock tailcone. Since we were redesigning the units to upgrade to the new model of AAT, we took the liberty of putting in a larger bearing, and redid the shaft to accommodate it. Expect much more longevity from your tailcone bearing! Description Part No. 1100 ZXI/STXR/STX12F/STX15F (04-06) KAW-1 Ultra 250 (07-08), Ultra 260 (09-10), KAW-4 Ultra 300 (11-12), STX15F (07-12) *This Kit does not contain Bearings and Impeller Shaft R&D ULTRA 250/260/300 1 DEGREE NOZZLE WEDGE KIT The R&D 1 Degree Reduction Nozzle Wedge Kit for the Ultra 250/260/300 will add quicker acceleration and top speed performance as well as allow the bow to ride slightly higher which will significantly reduce annoying bow spray promoting a much dryer ride. Extensive testing has led our development team to wedge the reduction nozzle up 1 full degree which will inexpensively give better handling everywhere and provide a boost of up to 1 mph in top speed performance. The billet aluminum CNC machined 1 degree reduction nozzle wedge kit was specifically designed to work without compromising or removing the O.E.M. reverse gate. The R&D Pump Wedge Kit comes complete with all the necessary hardware and instructions for easy installation. Description Part No. R&D Ultra 250/260 One Degree Nozzle Wedge Kit 141-25001 R&D Ultra 300 One Degree Nozzle Wedge Kit 141-30000 R&D ULTRA 250/260/300 DRIVESHAFT SHIM KIT The R&D driveshaft shims install into the prop snout and removes the unwanted play or float the driveshaft has in the prop/pump assembly. Properly shimming the driveshaft will keep the driveshaft couplers fully engaged eliminating premature rubber dampener wear and failure. Description Part No. R&D Ultra 250/260/300 Driveshaft Shim Kit 161-00810 R&D ULTRA 250/260/300 ANTI-CAVITATION PUMP CONE KIT The R&D Anti-Cavitation Pump Cone Kit was developed to reduce overall internal pump cavitation within the Ultra offset reduc- tion/compression nozzle design. The O.E.M. Reduction/Compression nozzle is offset 5 degrees, while the pump cone/bearing cap remains straight which causes uneven pressures within the pump and reduction nozzle. The R&D Anti-Cavitation Pump Cone is offset 5 degrees and reshaped to match the O.E.M. reduction nozzle offset promoting even pressures, which will substantially reduce cavitation, increase pump hook up, boost acceleration, and increase top speed performance. Description Part No. R&D Ultra 250/260/300 161-25010 Anti-Cavitation Pump Cone Kit ULTRA 250X (2008) PERFORMANCE DATA Stock 65 MPH @ 7,700 RPM Stage 1 70 MPH @ 7,850 RPM ULTRA 260X (2009-10) PERFORMANCE DATA Stock 67 MPH @ 7,860 RPM Stage 1 71 MPH @ 7,950 RPM Note: All testing performed with 1/3 tank of fuel. Stage 1 Performance Parts are sold individually. Description Quantity Part No. Performance Power Filter Kit 1 RS13090 Pro-Series Water Box 1 RK16091-1 Free Flow Exhaust Kit 1 RK16090-0 Top-Loader Intake Grate 1 RK22090 Performance Ride Plate 1 RK21090 Pro-Series Sponson Kit 1 RK26090 KAWASAKI ULTRA 250/260X RIVA STAGE 1 PARTS LIST