2010 Hot Products Catalog

39 YAMAHA 4 STROKE INATKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL YAMAHA FX-SHO & FZ • CONTROL • PUMP R&D FZR BILLET STEERING SYSTEM KITS The new R&D Billet Steering System was developed and tested during the 2009 APBA/IJSBA National and World Championships and is a proven winner in design and performance. R&D’s Billet design offers superior strength and lighter weight over the OEM steering system. Utilizing a 7/8” MX handlebar, allows the rider to personalize the bar setup to their liking. R&D chose the 7/8” diameter bar type over the Fat bar, because of the space water- craft bars need for start/stop switches, VTS switches, and custom trim lever systems. When using fat or taper bars, the bar widths are forced wider than comfortable in a watercraft application. R&D offers two types of Handlebars for the new billet steering system, MX Low for short to average height pilots and MX high for taller pilots. Handlebars sold separately. The R&D Steering System is the way to go when setting up the ergonomic steering comfort “your way”. Available for FZR/FZS and SHO models. Specify whether your craft is an FZR/FZS or SHO when ordering. • 3 pounds lighter than stock system • Easy installation (1hour) includes all hardware and instructions • Increases overall comfort and handling performance • Allows custom bar setups (set up your way) • Utilizes 7/8” diameter handlebars of our choice • Adds a true “Factory Racing” look to your watercraft Description Part No. FZR / FZS Billet Steering System 512-18000 FX-SHO Billet Steering System 512-18001 R&D MX Low Bar 512-18010 R&D MX High Bar 512-18012 SATO ENGINEERING FZR/FZS STEERING SYSTEM This billet steering system is the ultimate upgrade for the new Yamaha FZ watercraft. The system is extremely strong and allows the rider to change to handlebars of their choice. Description Part No. Sato Engineering FZR/FZS Steering System SE-027020 RIVA FX-SHO PUMP SEAL KIT Dramatically reduce cavitation and prop spin with our easy to install Pump Seal Kit. Location specific, molded inserts fill the voids in intake grate that can bleed air into pump causing cavitation. Specifically designed for craft using RIVA FX-SHO intake grate (part# RY22040). Includes detailed installation instructions. Description Part No. Riva FX-SHO Pump Seal Kit for Riva Intake Grate RY25040 Riva FZR/FZS Pump Seal Kit for Riva Intake Grate RY25050 SKAT-TRAK FX-SHO/FZR 155-75-25 SWIRL IMPELLERS RIVA Racing carries the complete line of Skat-Trak stainless steel Swirl impellers for Yamaha FX-SHO & FZ models. Let our performance experts assist you withmatching the correct impeller with your performance application. Includes a billet nose boot and impeller wrench. Description Part No. Skat-Trak FX-SHO/FZR/FZS 11/19 SY557525SW1119 Skat-Trak FX-SHO/FZR/FZS 12/19 SY557525SW1219 Skat-Trak FX-SHO/FZR/FZS 12/20 SY557525SW1220 Skat-Trak FX-SHO/FZR/FZS 13/20 SY557525SW1320 Skat-Trak FX-SHO/FZR/FZS 13/21 SY557525SW1321 Skat-Trak FX-SHO/FZR/FZS 13/22 SY557525SW1322 Skat-Trak FX-SHO/FZR/FZS 13/23 SY557525SW1323 Skat-Trak FX-SHO/FZR/FZS 13/24 SY557525SW1324 Skat-Trak FX-SHO/FZR/FZS 13/25 SY557525SW1325 RIVA SOLAS DYNAFLY R-SERIES IMPELLER This all new impeller delivers unmatched acceleration & top speed in Yamaha FX-SHO/FZ applications. The "R" Series impeller is precision tuned to RIVA specifications using a pitch block fixture. This offers a higher level of consistency when matched with RIVA Performance Kits. Includes billet impeller cone that locks solidly into place with 3 stainless set screws. Ideal for Riva Stage 1 applications or higher levels of modification when matched with RIVA Pro-Series FX-SHO/FZ Reduction Nozzle (part# RY23040-N). Description Part No. Riva Solas Dynafly Impeller 13/22R YS-DF-13/22R Solas Recommends: FX-SHO/FZ Stock Replacement Impeller YS-DF-14/21 FX-SHO/FZ Limited Boat Replacement Impeller YS-DF-15/22 FX-SHO/FZR/FZS IMPELLER SHAFT HOLDER TOOL Developed specifically for the FX-SHO/FZR/FZS watercraft, this tool is required to change the impeller. 20mm splined. Description Part No. FX-SHO/FZR/FZS Impeller Tool TOOL #53