2002 HotProducts Catalog

FUEL SYSTEMS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE/ BILGE BODY SERVICE TOOLS /HARDWARE CHEMICAL HANDLEBARS & CONTROLS ACCESSORIES ENGINE/ GASKETS 122 The best light bar available for boat trailers 80” or more in overall width. Three fully waterproof lamps are fastened on 6” centers to a stainless steel mounting bar. Also, the watertight lights are molded in durable polycarbonate for best damage resistance. The unit comes pre-wired with a 60” lead and can be mounted in many areas because of its low profile. Dimensions are 14-1/4” x 1-1/8” x 1”. Used on a variety of snowmobile and select boat trailers. A sonically welded, waterproof side marker or clearance light with reflex reflector. Mounting requires use of shock mount grommet kits for flush mount. Contains a 12 volt, .33 amp bulb rated at 2.0 candlepower. Display packaged. Features a sealed lamp capsule that protects the bulb and electrical contacts from damage and water corrosion. Inside the sealed cap- sule are long-lasting, automotive quality multi-functional tail- light and side marker bulbs. the capsule is easily replaceable. These units serve seven basic functions – tail light, stop light, turn signal, side and rear reflex reflector, red side marker light and red clearance light. The roadside (LH) light includes a built-in license plate illuminator. These lights easily can be flush or recess mount- ed and come with pre-installed wire leads. Overall dimensions are: 8”L x 2-7/8”H x 2-3/4”D. WATERPROOF LOW PROFILE TAIL LIGHT Part No. WB-3026 WB-3076 Description 8-Function Tail Light, Roadside (LH) 7-Function Tail Light, Curbside (RH) Part No. WB-3023 WB-3073 Description 7-Function Tail Light, Roadside (LH) 6-Function Tail Light, Curbside (RH) Widely used by jet ski and boat trailer manufacturers, these multi- function submersible tail lights are designed to protect the bulbs and contacts when the trailer is under water during launching and load- ing. They employ a “trapped air” technique to keep water from the bulbs. The bulbs and lenses are easily replaceable. Closed bottom design prevents splashing water and road grit from entering the lamp and meets all applicable DOT regulations. The lights come with pre- installed wire leads and two 1/4” mounting studs on 2” centers. SUBMERSIBLE TAIL LIGHT The most popular waterproof light in the marine industry today. Constructed of extra-tough poly- carbonate to resist breakage. The light bulb is contained in a permanently sealed compartment and comes with a pre-installed 15” lead wire. These lights may be used as a combination side marker and clearance light, when properly mounted (Note: Reflex reflector is not included). Overall dimensions are 2-1/8” x 1-1/8” x 1-1/16” (stud mount). WATERPROOF COMBINATION SIDE MARKER AND CLEARANCE LIGHTS Part No. WB-3233 Description Amber SM/Clearance Light, Stud Mount Part No. WB-3385 Description Amber SM/Clearance Light (10205Y/143A) Part No. WB-3315 Description Light Bar with red Waterproof Modules Part No. WB-3080 WB-106873 Description Tail Light, Complete Assembly (60010R/421KR) Mounting Bracket This popular waterproof lamp performs stop, turn and taillight func- tions. The virtually inde- structible, sonically sealed, polycarbonite lens and housing unit contains a heavy-duty shock mounted, dual fil- ament bulb. Mounts either vertically or hori- zontally in a flush mount grommet. Available as a kit including light, grommet, 3-way plug and grounding screw; light module only; 12 volt, 2.1/.48 amp and 32/2 candlepower, or grommet only. WATERPROOF OVAL TAIL LIGHT WATERPROOF IDENTIFICATION LIGHT BAR WATERPROOF ROUND 2.5” COMBINATION SIDE MARKER OR CLEARANCE LIGHT W/REFLEX TRAILER ACCESSORIES