Hot Products 2020 Catlog

Orders & Info: 858-453-4454 • HotProductsUSA.com 70 INTAKE SYSTEMS KAWASAKI 1500 SX-R ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2020 Hot Products. All rights reserved. KAWASAKI 1500 SX-R • PUMP SKAT-TRAK IMPELLER FOR STOCK PUMP Description Part No. For Bottom / Mid Range SK4875SW1317 For Top Speed SK4875SW1319R Replacement Nose Boots RIMPNOSEBOOTSD20 SOLAS IMPELLER Description Part No. Stock KGX-CD-15/20 Limited/MOD KGX-CD-12/16 SOLAS 148MM PUMP 12Vane, 148mm, 74mm Hub Description Part No. Solas 148mm pump stater KGX-HSV-148/74 HSV + impeller shaft + bearing + oil seal + cone Solas Complete Jet Pump KGX-PM-148/74T HSV + impeller shaft + bearing + oil seal + tail cone + nozzle + settering nozzle + trim ring REPLACEMENT SOLAS PARTS FOR KGX/KGS PUMP Description Part No. Impeller shaft 160820314803 Bolt Kit (set of 4) 85010067 M8 x 1.25 x 140 L Seal Kit 54-3700 (SCJ ID30xOD50xT7mm) x 2pcs (30x50x7/7.5) x 1 pc Seal and Bearing Kit 1608158001 for KGX Pump R&D HYDRO FORCE STEERING NOZZLE The new R&D Hydro Force Steering Nozzle for the SX-R is a cast aluminum lengthened design delivers a 1 mph speed gain and improves the turning radius. Allowing you to carve tighter turns with an increased positive feel. NOTE: Slight modification of the stock exit nozzle is necessary to install the R&D steering nozzle. Steering nozzle comes with instructions including blue- print of the modifications needed for stock exit nozzle. Description Part No. 1500 SX-R Hydro Force Steering Nozzle 161-81500 PUMP SEAL FOR KAWASAKI 1500 SX-R Description Part No. Pump Seal (OEM# 39145-3742) 003-551 R&D ADJUSTABLE ANTI-CAVITATION PUMP CONE The R&D Billet Adjustable Pump Cone Kit is a creative new bolt on part that adds additional length over the OEM cone, and comes complete with tuning spacers. The extended length allows custom RPM tuning, reduced cavitation and adds additional pump thrust. Precision tuning the pump cones length with the kit included cone spacers will add to top speed while keeping the engine RPMs stable and out of the rev limiter. Description Part No. For Stock Pump 161-00806 For Solas Pump 161-00807 SKAT-TRAK TRIM SYSTEM FOR KAWASAKI 1500 SX-R • 148 STOCK PUMP • Exit nozzle with 84 and 85mm nozzle rings • Steering nozzle 88mm (Short Nozzle) (Long Nozzle available upon request) • Pulley style trim ring assembly • Trim cable • Trim cable tube • Trim cable seals • Hardware for installation • Trim Lever sold separately, Hot Products recommends UMI Racing KA-01525-BLK, see page 269 1500 SX-R TRIM SYSTEM Part No. No Vane Exit Nozzle PRNKAW1500SXR0 6 Vane Exit Nozzle PRNKAW1500SXR6 7 Vane Exit Nozzle PRNKAW1500SXR7 Kawasaki Long Pulley Trim Cable PRSTKAWSXRTP WSM IMPELLER SHAFT Description OEM# Part No. 1500 SX-R 13107-0739 003-109-04 STX-15F 13107-0765 1500 X-R PROP REMOVAL TOOL The OEM Kawasaki 1500 SX-R pump shaft has a very small tail that is required to be held during impellor removal and installation. Due to the high horsepower and torque of the engine the impellor can be very tight and the pump shaft tail will twist during removal. This tool will allow you to hold the tail of the pump shafty securely in a vise and prevent damaging the pump shaft. A must have tool. Description Part No. A. 1500 SX-R Prop Removal Tool BM41-60-8 B. 1500 SX-R Impeller Shaft Holder Tool 57001-1393SXR KGX-PM-148/74T KGX-HSV-148/74 A. B.