2018 Hot Products Catalog

HotProductsUSA.com • Orders & Info: 858-453-4454 175 FOUR STROKE INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL © 2018 Hot Products. All rights reserved. SKAT-TRAK SEA-DOO 159MM PUMP IMPELLER SPACER/WASHER Due to manufacturing changes by Sea-Doo BRP, you might need this washer depending on the “Year” Sea-Doo PWC you have. If your stock impeller and pump look like the photos on the left, then you will need to install the Skat-Trak Sea-Doo impeller spacer/washer onto the back of the impeller inside the recessed area. Failure to do so can cause serious damage to your PWC. Skat-Trak will not be held liable for damage caused by improper impeller installation. All Sea-Doo 159mm Pump Skat-Trak Impellers now include this washer when shipped. Description Part No. Sea-Doo 159mm Pump spacer/washer for Skat-Trak Impellers RIMPPSPACERSD159 *This is only for the replacement use of spacer/washer for Skat-Trak Impellers ✔ 148MM NON SETBACK AND SETBACK PUMPS 148mmYamaha based Superjet/Waveblaster style and is a direct bolt in replacement for the 144mm pump. Torrent Pumps are one piece 148mm – 12 Vane – 75mm large hub pumps that increases throughput of water creating bot- tom end hit of 10-25% more right through top end pull for maximum amplitude. Distinct performance advantages over other two piece stainless steel pumps. 20-25% weight reduction. Set Back will require a Torrent set back shaft. Torrent recommends Skat-Trak impellors for all applications. 148mm Pump Assembly Configuration Part No. 148mm • 12 Vane Pump SET-BACK 148-SB-ASSEMB 148mm • 12 Vane Pump NON-SET-BACK 148-NSB-ASSEMB Torrent Pump complete assemblies are: Stator, Medium Tail Cone, Seals, Bearings and drive shaft. Does not include Impeller, Reduction Nozzle or Trim System 148mm Stator Only Configuration Part No. 148mm • 12 Vane Stator SET-BACK 148-02 148mm • 12 Vane Stator NON-SET-BACK 148-01 155MM SETBACK PUMPS 155mm Yamaha based housing for most aftermarket hulls. Torrent Pumps are one piece 155mm – 14 Vane – 75mm large hub pumps that increases throughput of water creating bottom end hit right through top end pull for maximum amplitude. 14 vane specifically made for performance in Freeride/Freestyle offering greater performance. 155mm Pump Assembly Configuration Part No. 155mm • 14 Vane Pump SET-BACK 155-SB-ASSEMB Torrent Pump complete assemblies are: Stator, Medium Tail Cone, Seals, Bearings and drive shaft. Does not include Impeller, Reduction Nozzle or Trim System 155mm Stator Only Configuration Part No. 155mm • 14 Vane Stator SET-BACK 155-02 A Torrent Extended Length Impeller Tool is highly recommended for Skat-Trak impeller removal and installation due to the one piece pump design. Description Part No. Torrent Extended Length Impeller Tool IMP-TOOL TORRENT DRIVE SHAFTS Billet one piece heavy duty drive shafts are made from a marine custom high quality alloy allowing exact specifications to tighter tolerances for longer life. 15 quality checks on each drive shaft and Shaft run out (bend) much tighter than OEM specifications which stop cavitation in front of the impeller, pro- motes longer bearing life and superior performance. Made in the USA from . Driveshaft Configuration Part No. 148mm SET-BACK 148-SB-DS-SJ96-07 148mm NON-SET-BACK 148-NSB-DS-SJ96-07 155mm SET-BACK 155-SB-DS-SJ96-07 TORRENT BEARING KITS Engineered to fit Torrent Pumps and H2O Designs Pumps utilizing only OEM components and hand checked to .0001 /.0025mm each batch to confirm precise fitment. Description Part No. 148/155mm Set-Back BRG-SEALKIT-SB 148mmNon Set-Back BRG-SEALKIT TORRENT PUMP SEALS Specifically designed for OEM as well as Torrent Pumps. Internal wire ring to stay put and low durometer doubled sealed flanges. Description Part No. 144/148 Pump Seal 148-PS 150/160 Pump Seal 155-PS TORRENT TAIL CONES Torrent Tail Cones are available in a range of volumes and shapes for specific applications, and tuning. We have developed these tail cones to mimic a 2mm bore size change of your reduction nozzle, or one degree leading edge for impeller pitch. Resin Construction makes us lighter than the competition, chemical resistant, and no galvanic corrosion. Medium 75mm tail cone is standard with 148, 155 Torrents. Small cone shown here adds a 2mm bore size to your reduction nozzle. Description Part No. Short 75mm TT-75MM-SHORT Medium 75mm (Standard) TT-75MM-MED Long 75mm TT-75MM-LONG

RkJQdWJsaXNoZXIy NjEwMDM=