Basic HTML Version
R&D YAMAHA
GP 1300R EXHAUST
POWER SLEEVE
The R&D GP 1300R Exhaust Power
Sleeve will add a serious boost to low end
and mid range horsepower and
performance! The R&D Exhaust Power
Sleeve installs between the exhaust
chamber and the catalytic housing to increase sonic wave energy! The
R&D Exhaust power Sleeve will add the Y.P.V.S. (power valve) feel to the
2005 Yamaha’s non-power valve engine!
Description
Part No.
Yamaha GP 1300R Exhaust Power Sleeve
332-13001
156
INTAKE
SYSTEMS
FOUR
STROKE
ENGINE/
GASKETS
EXHAUST
DRIVE LINE
HANDLING
ELECTRICAL
WATERLINE
/BILGE
STEERING
& CONTROLS
BODY
ACCESSORIES
SERVICE TOOLS
/HARDWARE
CHEMICAL
©2012 Hot Products. All rights reserved.
Description Part No.
RIVA Cat Temp Sensor Chip
RY115-20
Yamaha 1200/1300 Powervalve (66V/66T)
RIVA Cat Temp Sensor Chip is a must when removing the OEM catalytic
converter on Yamaha 1200 & 1300 Powervalve engines. The circuit is
designed to mimic the signal sent to the OEM CDI by the catalytic converter’s
temperature probe preventing CDI, flutters, warning devices and engine shut
downs due to cat removal. Can be used with stock or modified OEM CDI’s.
Plugs directly into factory wire harness.
RIVA CAT TEMP
SENSOR CHIP FOR
YAMAHA
GPR 1200 & 1300
Part No.
YE-155P
Description
JetWorks Catalytic Converter Removal Plate
R&D D-PLATE FOR YAMAHA
GP1200R/GP1300R,
XLL/XLT1200
The new R&D D-Plate takes the place of the stock catalytic converter and
delivers the best overall low, mid, peek and overall horsepower. The benefits
include reducing engine compartment temperatures created by the catalytic
converter and reliability of the complete stock exhaust assembly.
Part No.
332-12000
Description
R&D D-Plate
CATALYTIC CONVERTER
REMOVAL PLATE
FOR YAMAHA
GP1200R/GP13OOR,
XLL/XLT1200
This plate allows you to remove the catalytic converter easily and fills the
gap where the catalytic converter mounts on the OEM exhaust system.
Benefits include a cooler running exhaust system and ability to run any
kinds of two-stroke oil. The plate features a centrally located outlet
designed to give some beneficial back pressure but with much better
exhaust gas flow compared to an offset or cutout plate. This gives better
response and acceleration throughout the power band.
FOR COMPETITION USE ONLY
.
R&D BILLET EXHAUST VALVES FOR GPR
The R&D Billet Exhaust Valves reduce the clearance between the valve
and piston, this reduced clearance improves the seal which boosts the
valve down compressions ratio delivering greater bottom and mid-range
power. Directly replace OEM YPVS valve units.
Part No.
332-12002
332-12003
332-13000
Yamaha
GP800/GP1200R Exhaust Valve Kit (each)
Exhaust Valve Arm Only
GP1300R Exhaust Valve Kit (each)
332-12002
Part No.
010-495-10
010-495-05
Sea Doo
OEM No.
A.
Exhaust Valve Piston
420-854-449
B.
Exhaust Valve Bellow 290-260-723
A
.
B
.
WSM REPLACEMENT EXHAUST
VALVE PARTS FOR SEA DOO
R&D KAWASAKI 800
SXR EXHAUST POWER
SLEEVE
The new R&D billet aluminum Exhaust power Sleeve is designed to insert
into the stinger of the stock exhaust to reduce the stinger size thereby
increasing back pressure. This is a simple installation that will increase top
speed and add 100 RPM.
Description
Part No.
Kawasaki 800 SXR Exhaust Power Sleeve
331-80000
332-12003